Showing 122 results for Ph
F. Hosseinabadi, A. Rezaee-Bazzaz, M. Mazinani, B. Mohammad Sadeghi,
Volume 17, Issue 1 (3-2020)
Abstract
An experimental–numerical methodology was used in order to study the microstructural effects on stress state dependency of martensitic transformation kinetics in two different TRIP800 low alloy multiphase steels. Representative volume elements extracted from actual microstructure have been utilized for simulating the mechanical behavior of mentioned steels. The mechanical behavior for each constituent phases required in the model has been taken out from those reported in the literature. A stress invariant based transformation kinetics law has been used to predict the martensitic phase transformation during deformation. Crystallographic and thermodynamic theories of martensitic phase transformation have been utilized for estimating the constant parameters of the kinetics law, in a recently performed investigation, but the sensitivity of the transformation to the stress state remained as an adjusting parameter. The results of the current work show that the stress state sensitivity of martensitic phase transformation in the investigated steels is microstructure-dependent and the value of this parameter is almost equal to half of the bainite volume fraction. Therefore, the volume fraction of bainite in the low-alloy multiphase TRIP800 steels can be used as a first postulation for the value of the martensitic phase transformation sensitivity to the stress state and the microstructure based model previously developed for calculating the mechanical behavior of the TRIP800 steels can be utilized as a virtual design tool for development of TRIP steels having specific mechanical properties.
M. Mahdi, A. Abdul-Hameed, B. Ali, H.f Al-Taay,
Volume 17, Issue 1 (3-2020)
Abstract
Silicon nanowires (SiNWs) are synthesized through a metal-assisted chemical etching (MACE) method using Si(100) substrates and silver (Ag) as a catalyst. Scanning electron microscope (SEM) images confirmed that length of prepared SiNWs was increased when etching time increased. The prepared SiNWs demonstrated considerably low light reflectance at a wavelength range of 200–1100 nm. The photoluminescence (PL) spectra of the grown SiNWs showed a broad emission band peaked at a wavelength of about 750 nm. A solar cell and photodetector based on heterojunction SiNWs/PEDOT:PSS were fabricated using SiNWs that prepared with different etching time and its J–V, sensitivity, and time response were investigated. The conversion efficiency of fabricated solar cell was increased from 0.39% to 0.68% when wire length decreased from 24 µm to 21 µm, respectively. However, the sensitivity of the heterojunction SiNWs/PEDOT:PSS photodetector was decreased from 53774% to 36826% when wire length decreased from 24 µm to 21 µm, respectively.
I. Kakaravada, A. Mahamani, V. Pandurangadu,
Volume 17, Issue 1 (3-2020)
Abstract
In the present investigation, A356-TiB2/TiC composites with a various weight fractions (0, 2.5, 5 and 7.5%) were synthesized through a K2TiF6-KBF4-Graphite (C) reaction system. Formation of TiB2 and TiC particulates and their distribution are confirmed by various characterization techniques. The tensile properties such as ultimate strength, yield strength, young's modulus and percentage of elongation in addition to their failure behavior of these composites were studied at ambiance and high temperatures (100, 200 and 3000C). The increment in the volume fraction of the composite raises the hardness and the enhancement of hardness was reported up to 49% at 7.5% reinforced composite due to the strengthening effect. The density and porosity of fabricated composites were investigated. The rise in volume fraction of reinforcement phase declines the density and increase the porosity of composites. Further, the ultimate strength, yield strength, young's modulus is declining by raising the temperature. Result analysis illustrates that the 7.5% reinforced composite retaining the ultimate strength up to 84.4% and the ductility is raised by 27% at 3000C. Yield strength and young's modulus are also retained 74.31% and 71.09% respectively at the similar material and experimental conditions. The fracture surface analysis of the composites illustrates that, the ductile nature of failure appearance microscopically with the formation of fine dimples and voids on fracture surface at elevated temperatures. Cleavage facets and tear crumples observation indicates the brittle kind of failure at the ambient temperature. Findings from the experimental study provide the tensile behavior of the composites at the regular working temperature of the automobile engine piston.
S. Manafi, S. Joughehdoust,
Volume 17, Issue 2 (6-2020)
Abstract
In this research, calcium titanate (CaTiO3) hollow crystals have been successfully prepared via hydrothermal method. Titanium tetrachloride, calcium chloride dihydrate and potassium hydroxide were used as Ti, Ca and precipitating agent, respectively. The hydrothermal synthesis was performed at different temperatures and time durations. The negative amount of the Gibbs free energy shows the reactivity of the reaction at room temperature. Characterization of CaTiO3 was carried out using scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM) and X-ray diffraction (XRD). The optimum condition for preparing CaTiO3 is the sample kept in an autoclave at 300 ℃ for 3 h that requires less energy and time which consists of a high degree of crystallinity. In this research, tetragonal CaTiO3 hollow crystals have been successfully prepared via hydrothermal method. TiCl4, CaCl2.2H2O, and KOH were used as Ti, Ca and precipitating agent, respectively. The hydrothermal synthesis was performed at different temperatures and time durations. Characterization of CaTiO3 was carried out using SEM, HRTEM, and XRD. The sample kept in the autoclave at 300 ℃ for 3 h well crystallized and required less energy and time for synthesis. The powder has a homogenous dispersity of crystals with the range of nanometer to micrometer sizes which makes it a good candidate as a photocatalyst material
A. Nemati,
Volume 17, Issue 2 (6-2020)
Abstract
Synthesis of materials at nano scale is one of the main challenges in nanotechnology for different applications such as semiconductor, superconductors, electro-optics devices, advanced ceramics, refractories, diagnostic imaging and drug delivery. Semiconductors nanocrystals, known as “Quantum Dots”, have emerged as new generation of nanomaterials due to their unique optical, electrical and electrochemical properties, for variety of applications such as contrasts agents, fluorescent labels, localized targeted drug delivery and new generation of biosensors. Quantum dots advantages over traditional nanomaterials are due to quantum confinement effect, which bring broad absorption spectra, superior brightness and durability for different applications. The most important factor in developing nano carriers for biological applications is the toxicity, so recent researches have been focused on heavy metal-free formulations and nontoxic ceramics and polymers. So, one of the main goals in this paper is to explicate efficiencies and deficiencies of recent advances in quantum dot based formulations with the least toxicity for bioimaging, therapeutic and drug delivery applications. Another area of quantum dot’s application is the determination of dopamine (DA). Due to basic role of DA in some diseases like Parkinson and Schizophrenia, its determination is important and thus, it is desirable to develop new, simple and rapid analytical methods for the determination of DA with high selectivity and sensitivity, especially for diagnostic applications. Recently, developments in nanotechnology and preparations of semiconductors quantum dots cause open a new field in photo-electrochemical methods based on semiconductors quantum dots for determination of DA. In this review, an attempt was made to elaborate the mentioned goals of the paper in details.
S. Mortezaei, H. Arabi, H. Seyedein, A. Momeny, M. Soltanalinezhad,
Volume 17, Issue 3 (9-2020)
Abstract
Dynamic Recrystallization (DRX) is one of the likely mechanisms for fine-graining in metals and alloys. The dynamic recrystallization (DRX) phenomena occurs in different thermo-mechanical processing (TMP) conditions for various metallic materials. DRX depends on various materials and thermo-mechanical parameters such as temperature, strain rate, strain, stress and initial microstructure. in the present study, the restoration mechanism of the 17-7PH stainless steel has been investigated using a hot compression test under different conditions of thermo-mechanical treatment. The microstructural characteristics and the behavior of the hot deformation of the under study steel are investigated using flow curves and microstructure images obtained from optical microscopy. The results show that the maximum and steady state stresses are significantly affected by the strain rate and the deformation temperature. So that, the flow stress increases with decrease in the deformation temperature and increase in the strain rate. Microstructural studies confirm the occurrence of DRX as a restoration mechanism in the microstructure for the two phases of austenite and ferrite.
A. Thakur, G. Reddy,
Volume 17, Issue 3 (9-2020)
Abstract
Mercury, one of the common pollutants in water, is known to affect human health adversely upon exposure. It is released in water not only by various natural processes but also by human activities. Methods developed so far for the detection of mercuric ions in water have limitations like sensitivity range, complex setup, skillful operation etc. Silver nanoparticles, due to unique properties, have been explored by researchers to develop better detection systems. Stable silver nanoparticles can be easily synthesized by methods of green chemistry, its reaction with mercuric ion can be easily observed by changes in color and UV-Vis spectra. The absorbance data from UV-Vis spectra can also be used in quantifying mercury concentration. In this paper, stable silver nanoparticles synthesized using silver nitrate as precursor, sodium lignosulphonate (LS) as reducing and stabilizing agent under microwave radiation are explored for detection of mercuric ions in water. Formation of AgNP was confirmed by UV-Vis band at 403.5nm. The intensity of this band showed a proportional decrease with increasing Hg+2 concentration. Hg+2 ions were detected by a distinct color change at higher concentration of Hg+2 also. The limit of detection (LOD) calculated from the observed absorbance data to be 0.7 ppm.
A. Kazazi, S. M. Montazeri, S. M. A. Boutorabi,
Volume 17, Issue 4 (12-2020)
Abstract
In the present study, austempering heat treatment was performed on compacted graphite aluminum cast iron with the chemical composition of 4.8%wt Al, 3.2%wt C, 0.81%wt Ni, 0.37%wt Mn, and 0.02%wt Mg. This study aims to investigate the effect of aluminum additions and removal of silicon on the kinetics of austempering transformation of Fe-3.2%C alloy. The cast samples were austenitized at 900 °C for 120 min and the isothermal austempering heat treatment was performed at 200 °C, 300 °C and 400 °C for 5, 30, 60, 120 and 180 minutes, respectively. Kinetics of this transformation was studied by X-Ray diffraction (XRD) analysis. The effect of temperature and time on the microstructure and hardness of the austempered samples was investigated and discussed. The presence of Al was seen to prolonged formation of the carbides from high carbon austenite, and that expanded the process window in the austempering transformation. Besides, the lower bainitic ferrite phase was observed in the austempered samples at 200 °C and 300 °C. Increasing austempering temperature to 400 °C changed the lower bainite to upper bainite structure. The volume fraction of austenite reached its maximum level (34.6 %) after austempering the samples at 400 °C for 30 minutes.
Sh. Foroutan, M. Hashemian, A. Khandan,
Volume 17, Issue 4 (12-2020)
Abstract
In this article, a novel bio-nanocomposite consists of sodium alginate polymer-based graphene nanosheet enhanced incorporating wollastonite containing various amount of graphene nanosheet were produced using freeze-drying technique. The bio-nanocomposites were mechanically and biologically evaluated using tensile strength and biological test. The phase and topological characterization were conducted using scanning electron microscopy (SEM) and X-ray diffraction (XRD) technique. Subsequently, based upon Euler-Bernoulli and Timoshenko beam theories (EBT and TBT), the buckling responses of the porous bio-nanocomposite soft tissue are analyzed corresponding to various graphene amounts. In order to solve the governing equations a sufficient numerical solution is proposed. Elastic modulus and mass density of the porous bio-nanocomposite are extracted from the experimental tests. The obtained results indicated the sample with 1 wt% graphene sheet has shown proper mechanical and biological features. Therefore, the sample with 1 wt% graphene sheet can be used as potential case for light weight bone substitute applications.
R.s Krishna, J. Mishra, A. Adeniji, Sh. Das, S. Mohammed Mustakim,
Volume 17, Issue 4 (12-2020)
Abstract
The field of nanomaterial has greatly advanced in the last decade following a wider range of applications in the fields of electronics, automobiles, construction, and healthcare due to its extraordinary and ever-evolving properties. Synthesis of the nanomaterial plays a crucial role in redefining the current engineering and science field. At the same time, procuring an environment-friendly end product through eco-friendly solutions and sustainable processes is the key to many global problems. Green synthesis of nanomaterials like graphene and its derivatives involves mild reaction conditions and nontoxic precursors because it is simple, cost-effective, relatively reproducible, and often results in more stable materials. This paper primarily focuses on the green synthesis of graphene and its derivatives (graphene oxide & reduced graphene oxide) and geopolymers; a green technology for preparing graphene reinforced geopolymer composites. Various methods used globally for green synthesis of graphene and geopolymer are briefly discussed and this paper tries to integrate these two areas for a green end product. Possible applications of these green composites are also discussed to provide insights on the current growth and developments.
S. Das, R. Ghadai, A. Krishna, A. Trivedi, R. Bhujel, S. Rai, Sh. Ishwer, K. Kalita,
Volume 17, Issue 4 (12-2020)
Abstract
Graphene oxide (GO) and reduced graphene oxide (rGO) is a semiconductor device which finds its many applications in the various electronic devices. In the present study GO and rGO thin sheets have been grown over Si wafers using Hummer’s and modified Hummer’s method and a comparison in the properties of the coatings have been carried out. The morphology of the sheets characterized by SEM revealed similar transparent sheet like structure for both the chemical synthesis. The diffraction pattern of GO and rGO prepared with modified Hummer’s method showed peak shift to lower diffraction angle from 9.96 o to 9.63 o and 26.4 o to 26.3 o respectively. The diffraction peaks were observed at diffraction phase of 001 and 002 crystal plane. FTIR spectra revealed presence of oxygen functional groups in GO thin sheets whereas peaks for oxygen functionalities are absent in rGO. The polarization curve indicated similar corrosion resistance of GO and rGO thin sheets grown under Hummer’s and modified Hummer’s. Capacitive property of rGO is better than GO as observed by the electrochemical analysis of GO and rGO..Graphene oxide (GO) and reduced graphene oxide (rGO) is a semiconductor device which finds its many applications in the various electronic devices. In the present study GO and rGO thin sheets have been grown over Si wafers using Hummer’s and modified Hummer’s method and a comparison in the properties of the coatings have been carried out. The morphology of the sheets characterized by SEM revealed similar transparent sheet like structure for both the chemical synthesis. The diffraction pattern of GO and rGO prepared with modified Hummer’s method showed peak shift to lower diffraction angle from 9.96 o to 9.63 o and 26.4 o to 26.3 o respectively. The diffraction peaks were observed at diffraction phase of 001 and 002 crystal plane. FTIR spectra revealed presence of oxygen functional groups in GO thin sheets whereas peaks for oxygen functionalities are absent in rGO. The polarization curve indicated similar corrosion resistance of GO and rGO thin sheets grown under Hummer’s and modified Hummer’s. Capacitive property of rGO is better than GO as observed by the electrochemical analysis of GO and rGO.
Z. Abasali Karaj Abad, A. Nemati, A. Malek Khachatourian, M. Golmohammad,
Volume 17, Issue 4 (12-2020)
Abstract
The graphene oxide -TiO2 (GO-TiO2) and pre-reduced graphene oxide -TiO2 (rGO-TiO2) nanocomposites were fabricated successfully by hydrothermal method. The microstructure of synthesized nanocomposites was investigated using field emission scanning electron microscopy (FESEM) equipped with energy dispersive spectroscopy (EDS) analysis. Moreover, galvanostatic charge/discharge (GCD), cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS) methods in three electrode system were applied to evaluate electrochemical properties. The results revealed that nanoparticles distributed more uniformly on graphene sheets, at lower concentrations of TiO2. The rGO-TiO2 and GO-TiO2 nanocomposites showed 224 and 32 F/g specific capacitance at 5 mV s-1 scan rate in 1 M KOH aqueous electrolyte, respectively. The pre-reduction of graphene oxide is the main reason for the better electrochemical performance of rGO-TiO2 nanocomposite compared to GO-TiO2 nanocomposite.
H. Momeni, S. Shabestari, S.h. Razavi,
Volume 17, Issue 4 (12-2020)
Abstract
In this research, densification and shape distortion of the Al-Cu-Mg (Al2024) pre-alloyed powder compact in the supersolidus liquid phase sintering process (SLPS) were investigated. The effect of Sn on the sintering process was also studied. The powders were compacted at pressures ranging from 100 to 500 MPa in a cylindrical die. The sintering process was performed in a dry N2 atmosphere at various temperatures (580-620 ºC) for 30 min at a heating rate of 10 ºCmin-1. Results showed that the onset of densification process was observed at 600ºC and onset of distortion was occurred at 610ºC. Addition of 0.1 wt. %Sn to the alloy has increased the distortion of the samples produced from Al-Cu-Mg pre-alloyed powder, but their densification has been improved. The compact pressure of 200MPa caused the complete densification at the optimum sintering temperature and at the compact pressures greater than 200MPa; the sintered density was independent of green density.
Reza Soleimani Gilakjani, Seyed Hossein Razavi, Masoumeh Seifollahi,
Volume 18, Issue 1 (3-2021)
Abstract
Niobium addition is an appropriate approach for improvement of superalloy’s operation. The purpose of this study is twofold: (1) to investigate on the η and γ/ phase precipitations along with (2) to identify the high-temperature tensile properties in A286 and Nb-A286, as a modified type. The heat treatment of both alloys was carried out in a two-stage aging procedure at 760°C for 16 h and 820°C for 2 to 30 hours, following characterized by optical and Scanning electron (SEM-EDS) microscopies, differential thermal analysis (DTA) and high temperature tensile tests. The results showed that niobium addition was increased the volume fraction of γ/ phase, from 10.7% to 12%, decreased its size, from 94 to 71 nm, and rising the γ/-dissolution temperature from 987°C to 1007°C. Moreover, the γ/ to η phase transformation was sluggishly occurred in Nb-A286 due to more stable of γ/ precipitations. Furthermore, the Nb-A286 alloy demonstrates higher mechanical properties than A286 one, approximately 100MPa improvement, which it was contributed to the much large volume fraction and finer size of more stabilized γ/ phase.
Najwa Gouitaa, Lamcharfi Taj-Dine, Bouayad Lamfaddal, Abdi Farid, Mohamed Ounacer, Mohammed Sajieddine,
Volume 18, Issue 2 (6-2021)
Abstract
Prabhakar Kuppahalli, Ramaiah Keshavamurthy, Padmanathan Sriram, Ahobal Narayana,
Volume 18, Issue 2 (6-2021)
Abstract
The present investigation aims to synthesize RB031, RB032 manganese bronze alloys equivalent to HTB1 and HTB2 alloys with additions of silicon and to characterize them with the help of Microstructure and Mechanical properties. The methodology involves melting of alloy’s in a 300kg Coreless medium frequency induction furnace, casting them in Permanent and Shell moulds with optimum values of Zinc equivalent and retaining their high mechanical properties. The study includes the development and mechanical property measurements of the alloys synthesized. Characterization has been carried out using Optical Microscopy and Scanning Electron Microscopy with EDAX analysis for investiagtion of compositional variations and inquisition of hardness measurement & tensile properties. It is concluded from this work that RB032 alloy cast in Permanent moulds has superior hardness and tensile properties compared to Shell moulds and far exceeds that of NAB (AB2) alloys processed under similar conditions. Further, this investigation includes grain refinement by suitable Heat treatment studies to combat Hot Tearing since the strength is adequate enough with RB032 exhibiting higher hardness than other two alloys.
Saeid Karimi, Akbar Heidarpour, Samad Ghasemi,
Volume 18, Issue 2 (6-2021)
Abstract
In this research, expanded graphite (EG) was successfully fabricated using a simple ball milling process followed by hydrofluoric (HF, 10 wt. %) leaching. The effects of ball milling time (0-15 h) and leaching time (1-24 h) on the exfoliation of graphite were examined by XRD and Raman spectra. Furthermore, the morphological evaluation of the obtained expanded graphite samples was carried out by scanning electron microscopy (SEM). The XRD results of the ball-milled and HF treated samples showed a slight peak shift and broadening of (002) plane for expanded graphite compared to the precursor and HF-treated samples. Moreover, the intensity of the (002) planes remarkably decreased by the ball milling process but remained constant after HF treatment. Raman spectra of the samples confirmed the ordering process only in HF-treated specimens. Moreover, the intensity ratio of 2D1 to 2D2 band gradually increased with enhancing the HF treatment time up to 5 hours, indicating a decrement in the number of graphite layers by leaching in the HF solution.
Usha Vengatakrishnan, Kalyanaraman Subramanian, Vettumperumal Rajapand, Dhineshbabu Nattanmai Raman,
Volume 18, Issue 3 (9-2021)
Abstract
Copper oxide (CuO) nanostructure particles were prepared using KOH/NaOH catalyst by low cost precipitation method and characterized by powder X-ray diffraction (PXRD), scanning electron microscope (SEM) and energy dispersive X-ray spectra (EDX) analysis. The photocatalytic dye degradation study of pure CuO nanostructure particles are analysed against two azo dyes (Direct black 38 (Black-E) and Congo red) under ultraviolet (UV) and solar irradiation. The release of major active species (*OH) in the photocatalytic degradation by as prepared CuO nanostructure particles were investigated by photoluminescence (PL) spectra with two different excitation wavelength (325and 355nm). The band gap of CuO nanostructure particles was calculated from diffuse reflectance spectra. The photocatalytic effect of CuO nanostructure particles is confirmed from the UV – Vis and photoluminescence spectra and also, further confirmed from the kinetic studies under UV and solar radiations. The photocatalytic degradation results revealed that 16.35% and 7.5% of black E and Congo red dye was degraded under UV, while it was 47.2% and 17.6% under solar light. The influence of pH on the photodegradation and change in the reaction temperature under solar irradiation were also analysed
Mitra Ghannadi, Hediye Hosseini, Bagher Mohammad Sadeghi, Bahman Mirzakhani, Mohammad Tahaaha Honaramooz,
Volume 18, Issue 3 (9-2021)
Abstract
The objective of the present paper is to investigate the effects of rapid heating and cryogenic cooling on on the microstructure and tensile properties of Al-Cu-Mg. The specimens were subjected to three heat treatment cycles in which the Infrared heating (IR) were used as the heating medium at the ageing stage, and the liquid nitrogen and water were used as the quenching mediums. The ageing temperature and time were 190⁰C and from 2 hours to 10 hours, respectively.The results indicated that by using IR at the ageing stage, the hardening rate enhanced because the rapid heating via this method leads to faster diffusion of the alloying elements. Moreover, the high density of nano-sized precipitates formed during ageingleads to higher strength and suitable ductility. Cryogenic treatment showed a negligible effect on both microstructure and tensile properties; however, it improved ductility. Overall, the combination of a high heating rate and cryogenic treatment led to the highest mechanical properties. SEM micrograph of the fracture surface of alloy demonstrated that in Cryogenic treatment+Artificial Ageing (CAA) condition, the surface had been fully covered by deep dimples in contrast to the Cryogenic treatment+Infrared Heating (CIR) and Water-Quench+ Infrared Heating (QIR) conditions which their dimples were shallow and also some facets were observed.
Arian Heidar Alaghband, Azam Moosavi, Saeid Baghshahi, Ali Khorsandzak,
Volume 18, Issue 3 (9-2021)
Abstract
Porous nanostructured SnO2 with a sheet-like morphology was synthesized through a simple green substrate-free gelatin-assisted calcination process using Tin tetracholoride pentahydrate as the SnO2 precursor and porcine gelatin as the template. Crystalline phase, morphology, microstructure, and optical characteristics of the as-prepared material were also investigated at different calcination temperatures using X-ray diffraction (XRD), Field emission scanning electron microscopy (FESEM), UV-visible absorption, and Photoluminescence spectroscopy (PL), respectively. XRD patterns of all the samples revealed the presence of a tetragonal crystalline structure with no other crystalline phases. Moreover, the synthesized hierarchical sheets assembled with nanoparticles displayed a large surface area and porous nanostructure. The calculated optical band gap energy varied from 2.62 to 2.87 eV depending on the calcination temperature. Finally, photoluminescence spectra indicated that the nanostructured SnO2 could exhibit an intensive UV-violet luminescence emission at 396 nm, with shoulders at 374, violet emission peaks at 405 and 414 nm, blue-green emission peak at 486 nm, green emission peak at 534 nm and orange emission peak at 628 nm.
